Braveators Engineering LLP

Vacuum systems are surrounded by the earth’s atmosphere. To create vacuum, it is necessary to pump air out of a system. The internationally accepted unit of vacuum measurement is the Torr.

The Steam Jet Ejector consists of three basic parts: Steam nozzle, Suction Chamber and Diffuser. Steam enters the motive steam nozzle from the steam chest. The nozzle extension is used to establish the position of the motive steam nozzle relative to the diffuser inlet. High pressure motive steam expands across a converging-diverging nozzle and is thus accelerated to a supersonic velocity.

The high velocity motive stream entrain the mixture is accomplished across the diffuser by conversion of velocity to pressure head. This is converted to velocity head in the motive steam nozzle, velocity heads is converted to pressure head in diffuser.

Steam Jet Ejector offer an economical means producing vacuum. It has no any moving parts, simple operation.

Ejector construction:

The ease of Steam Jet Ejector design permits fabrication from any welded material i.e. Carbon Steel, Stainless Steel, Hastelloy, Titanium, Graphite construction.

No of Stages:

Single Stage Ejector creates vacuum from atmospheric to 75 mm Hg A based on provided steam pressure. Higher vacuum more than 1 mm Hg A, may be achieved by multistage ejector. Multi stage ejector require either Barometric or Indirect type condensers. Condenser is require to reduce steam under certain conditions, recover condensate.

Ejector can handle process gases i.e. air, water vapour, SO2, Hexane, Toluene, EG and many other organic & inorganic vapours.

We “Engimech” supplies complete packages which includes ejectors, condensers, piping, valves, skid etc.,

Type of  Ejector Vacuum System

· Steam Jet Vacuum System

· Liquid Jet Vacuum System

· Steam + Liquid Jet Vacuum System

· Air Jet Vacuum System

· Rotajet Vacuum System

· Steam + Rotajet Vacuum System

· Liquid + Rotajet Vacuum System

· Thermo Vapor Compressor

MOC

· Metallic (SS304, SS316, MS, CS , DUPLEX , SUPERDUPLEX , ETC.. )

· Non Metallic (PP , GRAPHITE , ETC..)

Vacuum systems are surrounded by the earth’s atmosphere. To create vacuum, it is necessary to pump air out of a system. The internationally accepted unit of vacuum measurement is the Torr.

The Steam Jet Ejector consists of three basic parts: Steam nozzle, Suction Chamber and Diffuser. Steam enters the motive steam nozzle from the steam chest. The nozzle extension is used to establish the position of the motive steam nozzle relative to the diffuser inlet. High pressure motive steam expands across a converging-diverging nozzle and is thus accelerated to a supersonic velocity.

The high velocity motive stream entrain the mixture is accomplished across the diffuser by conversion of velocity to pressure head. This is converted to velocity head in the motive steam nozzle, velocity heads is converted to pressure head in diffuser.

Steam Jet Ejector offer an economical means producing vacuum. It has no any moving parts, simple operation.

Ejector construction:

The ease of Steam Jet Ejector design permits fabrication from any welded material i.e. Carbon Steel, Stainless Steel, Hastelloy, Titanium, Graphite construction.

No of Stages:

Single Stage Ejector creates vacuum from atmospheric to 75 mm Hg A based on provided steam pressure. Higher vacuum more than 1 mm Hg A, may be achieved by multistage ejector. Multi stage ejector require either Barometric or Indirect type condensers. Condenser is require to reduce steam under certain conditions, recover condensate.

Ejector can handle process gases i.e. air, water vapour, SO2, Hexane, Toluene, EG and many other organic & inorganic vapours.

We “Engimech” supplies complete packages which includes ejectors, condensers, piping, valves, skid etc.,

Type of  Ejector Vacuum System

· Steam Jet Vacuum System

· Liquid Jet Vacuum System

· Steam + Liquid Jet Vacuum System

· Air Jet Vacuum System

· Rotajet Vacuum System

· Steam + Rotajet Vacuum System

· Liquid + Rotajet Vacuum System

· Thermo Vapor Compressor

MOC

· Metallic (SS304, SS316, MS, CS , DUPLEX , SUPERDUPLEX , ETC.. )

· Non Metallic (PP , GRAPHITE , ETC..)