Braveators Engineering LLP

Vacuum systems are surrounded by the earth’s atmosphere. To create vacuum, it is necessary to pump air out of a system. The internationally accepted unit of vacuum measurement is the Torr.

The Steam Jet Ejector consists of three basic parts: Steam nozzle, Suction Chamber and Diffuser. Steam enters the motive steam nozzle from the steam chest. The nozzle extension is used to establish the position of the motive steam nozzle relative to the diffuser inlet. High pressure motive steam expands across a converging-diverging nozzle and is thus accelerated to a supersonic velocity.

The high velocity motive stream entrain the mixture is accomplished across the diffuser by conversion of velocity to pressure head. This is converted to velocity head in the motive steam nozzle, velocity heads is converted to pressure head in diffuser.

Steam Jet Ejector offer an economical means producing vacuum. It has no any moving parts, simple operation.

Ejector construction:

The ease of Steam Jet Ejector design permits fabrication from any welded material i.e. Carbon Steel, Stainless Steel, Hastelloy, Titanium, Graphite construction.

No of Stages:

Single Stage Ejector creates vacuum from atmospheric to 75 mm Hg A based on provided steam pressure. Higher vacuum more than 1 mm Hg A, may be achieved by multistage ejector. Multi stage ejector require either Barometric or Indirect type condensers. Condenser is require to reduce steam under certain conditions, recover condensate.

Ejector can handle process gases i.e. air, water vapour, SO2, Hexane, Toluene, EG and many other organic & inorganic vapours.

We “Engimech” supplies complete packages which includes ejectors, condensers, piping, valves, skid etc.,

 

Type of  Ejector Vacuum System

· Steam Jet Vacuum System

· Liquid Jet Vacuum System

· Steam + Liquid Jet Vacuum System

· Air Jet Vacuum System

· Rotajet Vacuum System

· Steam + Rotajet Vacuum System

· Liquid + Rotajet Vacuum System

· Thermo Vapor Compressor

MOC

· Metallic (SS304, SS316, MS, CS , DUPLEX , SUPERDUPLEX , ETC.. )

· Non Metallic (PP , GRAPHITE , ETC..)

 

Zero Liquid Discharge (ZLD) / Multi Effect Evaporation (MEE) plants are now necessary in the modern world. The ZLD plant is a cutting-edge technology thatreduces liquid waste from industrial operations and transforms it into solids that can be securely disposed of without harming the environment and clean water forreuse. By-products created during the process can potentially be recovered and sold to generate additional revenue.For this we can use the combination of the heat exchangers , vapor liquid separator , transfer and circulations pump , salt separation technology , etc..  Evaporation Plant Types  1. Falling Film Evaporation Plant.  2. Forced Circulation Evaporation Plant. 3. Natural Circulation Evaporation Plant. 4. Rising Film Evaporation Plant. 5. With-Out TVR based Evaporation Plant (Steam)6. TVR based Evaporation Plant. 7. MVR based Evaporation Plant.8. Thermic Fluid Heater based Evaporation Plant , Etc... Application of the Evaporation Plants. 1. To Achieving the ZLD norms as per the GPCB/CPCB.2. Product concentration. 3. Volume reduction.4. Salt recovery (Sodium Sulphate , Sodium Chloride , Glauber Salt , Etc..)5. Caustic Concentration. 6. Etc.. This is the mechanical equipment , design basic on the thermal calculation considering the concentration of the solids at the inlet , heating source availability ,        boiling point rise , application considering the general engineering practice (GEP) , ASME , TEMA , etc..  

Vacuum systems are surrounded by the earth’s atmosphere. To create vacuum, it is necessary to pump air out of a system. The internationally accepted unit of vacuum measurement is the Torr.

The Steam Jet Ejector consists of three basic parts: Steam nozzle, Suction Chamber and Diffuser. Steam enters the motive steam nozzle from the steam chest. The nozzle extension is used to establish the position of the motive steam nozzle relative to the diffuser inlet. High pressure motive steam expands across a converging-diverging nozzle and is thus accelerated to a supersonic velocity.

The high velocity motive stream entrain the mixture is accomplished across the diffuser by conversion of velocity to pressure head. This is converted to velocity head in the motive steam nozzle, velocity heads is converted to pressure head in diffuser.

Steam Jet Ejector offer an economical means producing vacuum. It has no any moving parts, simple operation.

Ejector construction:

The ease of Steam Jet Ejector design permits fabrication from any welded material i.e. Carbon Steel, Stainless Steel, Hastelloy, Titanium, Graphite construction.

No of Stages:

Single Stage Ejector creates vacuum from atmospheric to 75 mm Hg A based on provided steam pressure. Higher vacuum more than 1 mm Hg A, may be achieved by multistage ejector. Multi stage ejector require either Barometric or Indirect type condensers. Condenser is require to reduce steam under certain conditions, recover condensate.

Ejector can handle process gases i.e. air, water vapour, SO2, Hexane, Toluene, EG and many other organic & inorganic vapours.

We “Engimech” supplies complete packages which includes ejectors, condensers, piping, valves, skid etc.,

 

Type of  Ejector Vacuum System

· Steam Jet Vacuum System

· Liquid Jet Vacuum System

· Steam + Liquid Jet Vacuum System

· Air Jet Vacuum System

· Rotajet Vacuum System

· Steam + Rotajet Vacuum System

· Liquid + Rotajet Vacuum System

· Thermo Vapor Compressor

MOC

· Metallic (SS304, SS316, MS, CS , DUPLEX , SUPERDUPLEX , ETC.. )

· Non Metallic (PP , GRAPHITE , ETC..)

 

Vacuum systems are surrounded by the earth’s atmosphere. To create vacuum, it is necessary to pump air out of a system. The internationally accepted unit of vacuum measurement is the Torr.

The Steam Jet Ejector consists of three basic parts: Steam nozzle, Suction Chamber and Diffuser. Steam enters the motive steam nozzle from the steam chest. The nozzle extension is used to establish the position of the motive steam nozzle relative to the diffuser inlet. High pressure motive steam expands across a converging-diverging nozzle and is thus accelerated to a supersonic velocity.

The high velocity motive stream entrain the mixture is accomplished across the diffuser by conversion of velocity to pressure head. This is converted to velocity head in the motive steam nozzle, velocity heads is converted to pressure head in diffuser.

Steam Jet Ejector offer an economical means producing vacuum. It has no any moving parts, simple operation.

Ejector construction:

The ease of Steam Jet Ejector design permits fabrication from any welded material i.e. Carbon Steel, Stainless Steel, Hastelloy, Titanium, Graphite construction.

No of Stages:

Single Stage Ejector creates vacuum from atmospheric to 75 mm Hg A based on provided steam pressure. Higher vacuum more than 1 mm Hg A, may be achieved by multistage ejector. Multi stage ejector require either Barometric or Indirect type condensers. Condenser is require to reduce steam under certain conditions, recover condensate.

Ejector can handle process gases i.e. air, water vapour, SO2, Hexane, Toluene, EG and many other organic & inorganic vapours.

We “Engimech” supplies complete packages which includes ejectors, condensers, piping, valves, skid etc.,

 

Type of  Ejector Vacuum System

· Steam Jet Vacuum System

· Liquid Jet Vacuum System

· Steam + Liquid Jet Vacuum System

· Air Jet Vacuum System

· Rotajet Vacuum System

· Steam + Rotajet Vacuum System

· Liquid + Rotajet Vacuum System

· Thermo Vapor Compressor

MOC

· Metallic (SS304, SS316, MS, CS , DUPLEX , SUPERDUPLEX , ETC.. )

· Non Metallic (PP , GRAPHITE , ETC..)

 

Vacuum systems are surrounded by the earth’s atmosphere. To create vacuum, it is necessary to pump air out of a system. The internationally accepted unit of vacuum measurement is the Torr.

The Steam Jet Ejector consists of three basic parts: Steam nozzle, Suction Chamber and Diffuser. Steam enters the motive steam nozzle from the steam chest. The nozzle extension is used to establish the position of the motive steam nozzle relative to the diffuser inlet. High pressure motive steam expands across a converging-diverging nozzle and is thus accelerated to a supersonic velocity.

The high velocity motive stream entrain the mixture is accomplished across the diffuser by conversion of velocity to pressure head. This is converted to velocity head in the motive steam nozzle, velocity heads is converted to pressure head in diffuser.

Steam Jet Ejector offer an economical means producing vacuum. It has no any moving parts, simple operation.

Ejector construction:

The ease of Steam Jet Ejector design permits fabrication from any welded material i.e. Carbon Steel, Stainless Steel, Hastelloy, Titanium, Graphite construction.

No of Stages:

Single Stage Ejector creates vacuum from atmospheric to 75 mm Hg A based on provided steam pressure. Higher vacuum more than 1 mm Hg A, may be achieved by multistage ejector. Multi stage ejector require either Barometric or Indirect type condensers. Condenser is require to reduce steam under certain conditions, recover condensate.

Ejector can handle process gases i.e. air, water vapour, SO2, Hexane, Toluene, EG and many other organic & inorganic vapours.

We “Engimech” supplies complete packages which includes ejectors, condensers, piping, valves, skid etc.,

 

Type of  Ejector Vacuum System

· Steam Jet Vacuum System

· Liquid Jet Vacuum System

· Steam + Liquid Jet Vacuum System

· Air Jet Vacuum System

· Rotajet Vacuum System

· Steam + Rotajet Vacuum System

· Liquid + Rotajet Vacuum System

· Thermo Vapor Compressor

MOC

· Metallic (SS304, SS316, MS, CS , DUPLEX , SUPERDUPLEX , ETC.. )

· Non Metallic (PP , GRAPHITE , ETC..)